SILVER AUTOMATION INSTRUMENTS LTD.
Product Category

Balanced Flow Meter

Balanced Flow Meter

  • Orifice Plate Flow Meter

    Orifice Plate Flow Meter

    What is Orifice Plate Flow Meter?An orifice plate flow meter is a devicewith a hole in it, the function of which is for ...

  • Wedge Flow Meter

    Wedge Flow Meter

    Wedge Flow meter overviewA wedge flow meter is a flow measuringdevice or instrument that calculated the flow rate of liq...

Balanced Flow Meter Features

  • High accuracy

Multi hole balanced flow sensor is actually a flow rectifier, can effectively eliminate swirl and distorted velocity distribution improvements, the ideal state of the flow field approximation, the conventional measure for level 0.5, high accuracy measurement for level 0.2.

  • High turn down ratio

Multi hole balanced flow sensor is a with multi holes, select the appropriate equivalent diameter ratio, favor the lower limit of the flow also give consideration to the upper limit flow ,making the conventional measure flow turndown ratio of 10:1, if appropriate parameter selection, turndown ratio can be raised to 20: 1 ~ 30:1


  • Low requirement for straight pipe

Balanced flow sensor can adjust the flow stable and pressure recovery 2 times faster than conventional orifice throttling device, greatly reducing the requirement for straight pipe. Lower straight pipe section can be as small in most cases 0.5D ~ 2D, a balanced flow meter can save a lot of straight pipe sections, in particular pipe with expensive special materials.


  • Low Pressure loss

Balanced flow meter multi hole symmetrical design reduces the formation of vortices and turbulence of friction, reducing the kinetic energy loss. In the same working condition without reducing the differential pressure, balance flow meter can reduce 1/2~1/3 permanent pressure loss comparing with the conventional throttle device to reduce the cost.


  • Good repeatability and long-term stability

Balanced flow sensor of SILVER AUTOMATION INSTRUMENTS is with stable flow to improved repeatability up 0.1%.
Balanced flow meter multiple circulation holes dispersed by force, no acute wear, its β value of long-term unchanged to maintain stability, the whole instrument with no moving parts , extend the service life of 5 to 10 times faster than conventional throttling device .


  • Not easy to block by dirty

Porous symmetrical balanced design reduces the formation of vortex turbulent shear force fit , thereby greatly reducing the formation of dead zone residence , dirty media to ensure a plurality of holes pass , reducing the chance of fluid holes are blocked .


  • Wide application range

Working temperature and pressure of balanced flow sensor is decided by pipe and flange material, it can reach to 800 ℃, 42MPa or higher temperature, pressure medium. Suitable for cryogenic fluid LNG \ liquid air , liquid ammonia , liquid oxygen, liquid fluoride , liquefied ethylene, liquid hydrogen , chlorine , etc., can effectively prevent vaporization , measuring good effect.


Balanced Flow Meter Model Selection

Item

Code

Description

Product

SD14

Balanced Flow Meter

Mounting

W

F

H

FF

FT

FS

FV

J

S

Z

Wafer type

Flange type

Direct Welding

Flange Taping

Special Material of Double flange

Anti-corrosion Type

Heating Jacket

Square TubeType

Integral Installation Type

Others

Size

xxx

For example, 150 stands for DN150

Housing Material

A

B

C

D

E

Z

Carbon Steel

304 Stainless steel

316L stainless steel

High temperature alloy

PTFE lined carbon steel

Others

Sensor Material

A

B

C

D

E

Z

304 Stainless steel

316L stainless steel

HC-276

Monel 400

Inconel635

Others

Pressure Rating

1

2

3

4

5

6

7

8

9

A1

A2

A3

A4

A5

Z

PN0.6

PN1.0

PN1.6

PN2.5

PN4

PN6.4

PN10

PN16

PN25

CL150(ANSI/ASME)

CL300(ANSI/ASME)

CL600(ANSI/ASME)

CL900(ANSI/ASME)

CL1500(ANSI/ASME)

Others

Tapping Type

A

B

C

D

Z

NPT (Thread type)

PSW (Direct Welding)

1” Flange

2” Flange

Others

Accessories

P

E

F

G

Differential Pressure Transmitter

Companion Flanges (bolts, nuts, gasket included)

Siphon

3-way manifold


Note:

1. Wafer type with NPT thread tapping: DN10~DN40, C=1/4, DN50~DN3000,C=1/2”

2. Only Flange tapping available for heating jack type, DN40~DN50 1” Flange, DN80~DN350 2” flange.

Leave a Message Email Us

we will contact you within 24 hours.

DMCA.com Protection Status